# Example config file /etc/vsftpd.conf
#
# The default compiled in settings are fairly paranoid. This sample file loosens things up a bit, to make the ftp
# daemon more usable. Please see vsftpd.conf.5 for all compiled in defaults.
#
# READ THIS: This example file is NOT an exhaustive list of vsftpd options. Please read the vsftpd.conf.5 manual
# page to get a full idea of vsftpd's capabilities.
#
#
# Run standalone?  vsftpd can run either from an inetd or as a standalone daemon started from an initscript.
listen=NO
#
# This directive enables listening on IPv6 sockets. By default, listening on the IPv6 "any" address (::) will
# accept connections from both IPv6 and IPv4 clients. It is not necessary to listen on *both* IPv4 and IPv6
# sockets. If you want that (perhaps because you want to listen on specific addresses) then you must run two
# Example config file /etc/vsftpd.conf
#
# The default compiled in settings are fairly paranoid. This sample file loosens things up a bit, to make the ftp
# daemon more usable. Please see vsftpd.conf.5 for all compiled in defaults.
#
# READ THIS: This example file is NOT an exhaustive list of vsftpd options. Please read the vsftpd.conf.5 manual
# page to get a full idea of vsftpd's capabilities.
#
#
# Run standalone?  vsftpd can run either from an inetd or as a standalone daemon started from an initscript.
listen=NO
#
# This directive enables listening on IPv6 sockets. By default, listening on the IPv6 "any" address (::) will
# accept connections from both IPv6 and IPv4 clients. It is not necessary to listen on *both* IPv4 and IPv6
# sockets. If you want that (perhaps because you want to listen on specific addresses) then you must run two
# copies of vsftpd with two configuration files.
listen_ipv6=Yes
#
# Allow anonymous FTP? (Disabled by default).
anonymous_enable=NO
#
# Uncomment this to allow local users to log in.
local_enable=YES
#
# Uncomment this to enable any form of FTP write command.
write_enable=YES
#
# Default umask for local users is 077. You may wish to change this to 022, if your users expect that (022 is used
#by most other ftpd's) local_umask=022
#
# Uncomment this to allow the anonymous FTP user to upload files. This only has an effect if the above global
#write enable is activated. Also, you will obviously need to create a directory writable by the FTP user.
#anon_upload_enable=YES
#
# Uncomment this if you want the anonymous FTP user to be able to create new directories.
#anon_mkdir_write_enable=YES
#
# Activate directory messages - messages given to remote users when they go into a certain directory.
dirmessage_enable=YES
#
# If enabled, vsftpd will display directory listings with the time in your local time zone.  The default is to
# display GMT. The times returned by the MDTM FTP command are also affected by this option.
###use_localtime=YES
use_localtime=NO
#
# Activate logging of uploads/downloads.
xferlog_enable=YES
#
# Make sure PORT transfer connections originate from port 20 (ftp-data).
connect_from_port_20=YES
#
# If you want, you can arrange for uploaded anonymous files to be owned by a different user. Note! Using "root"
#for uploaded files is not recommended! chown_uploads=YES chown_username=whoever
#
# You may override where the log file goes if you like. The default is shown below.
#xferlog_file=/var/log/vsftpd.log
#
# If you want, you can have your log file in standard ftpd xferlog format. Note that the default log file location
#is /var/log/xferlog in this case. xferlog_std_format=YES
#
# You may change the default value for timing out an idle session. idle_session_timeout=600
#
# You may change the default value for timing out a data connection. data_connection_timeout=120
#
# It is recommended that you define on your system a unique user which the ftp server can use as a totally
#isolated and unprivileged user. nopriv_user=ftpsecure
#
# Enable this and the server will recognise asynchronous ABOR requests. Not recommended for security (the code is
#non-trivial). Not enabling it, however, may confuse older FTP clients. async_abor_enable=YES
#
# By default the server will pretend to allow ASCII mode but in fact ignore the request. Turn on the below options
#to have the server actually do ASCII mangling on files when in ASCII mode. Beware that on some FTP servers, ASCII
#support allows a denial of service attack (DoS) via the command "SIZE /big/file" in ASCII mode. vsftpd predicted
#this attack and has always been safe, reporting the size of the raw file. ASCII mangling is a horrible feature of
#the protocol. ascii_upload_enable=YES ascii_download_enable=YES
#
# You may fully customise the login banner string: ftpd_banner=Welcome to blah FTP service.
#
# You may specify a file of disallowed anonymous e-mail addresses. Apparently useful for combatting certain DoS
#attacks. deny_email_enable=YES
# (default follows) banned_email_file=/etc/vsftpd.banned_emails
#
# You may restrict local users to their home directories.  See the FAQ for the possible risks in this before using
#chroot_local_user or chroot_list_enable below. chroot_local_user=YES
#
# You may specify an explicit list of local users to chroot() to their home directory. If chroot_local_user is
#YES, then this list becomes a list of users to NOT chroot(). (Warning! chroot'ing can be very dangerous. If using
#chroot, make sure that the user does not have write access to the top level directory within the chroot)
#chroot_local_user=YES chroot_list_enable=YES
# (default follows) chroot_list_file=/etc/vsftpd.chroot_list
#
# You may activate the "-R" option to the builtin ls. This is disabled by default to avoid remote users being able
#to cause excessive I/O on large sites. However, some broken FTP clients such as "ncftp" and "mirror" assume the
#presence of the "-R" option, so there is a strong case for enabling it. ls_recurse_enable=YES
#
# Customization
#
# Some of vsftpd's settings don't fit the filesystem layout by default.
#
# This option should be the name of a directory which is empty.  Also, the directory should not be writable by the
# ftp user. This directory is used as a secure chroot() jail at times vsftpd does not require filesystem access.
secure_chroot_dir=/var/run/vsftpd/empty
#
# This string is the name of the PAM service vsftpd will use.
pam_service_name=vsftpd
#
# This option specifies the location of the RSA certificate to use for SSL encrypted connections.
rsa_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem rsa_private_key_file=/etc/ssl/private/ssl-cert-snakeoil.key
ssl_enable=NO